question about pin pullar cabling on magnetometer on Pioneer Orbiter, question about pin pullar cabling on magnetometer on Pioneer Orbiter |
question about pin pullar cabling on magnetometer on Pioneer Orbiter, question about pin pullar cabling on magnetometer on Pioneer Orbiter |
May 29 2013, 04:22 PM
Post
#1
|
|
Junior Member Group: Members Posts: 91 Joined: 21-August 06 Member No.: 1063 |
Does anyone know currently any of the engineers or scientists who worked directly on the Pioneer Venus Orbiter? Are they all dead or retired now? I have a specific yet simple question about how the pin puller latch locks cabling was attached or ran along the magnetometer boom. Ideally this person would have to have seen the real pioneer orbiter to answer the question.
All nasa pdfs info and photos I have found are inconclusive. I would prefer an expert as oppossed to lots of guesses. It would be easy question for them since they would have seen the real orbiter. thanks |
|
|
May 29 2013, 06:33 PM
Post
#2
|
|
Founder Group: Chairman Posts: 14434 Joined: 8-February 04 Member No.: 1 |
I assume you've found the model hanging in the Smithsonian to be lacking somehow?
Doug |
|
|
May 29 2013, 09:29 PM
Post
#3
|
|
Junior Member Group: Members Posts: 91 Joined: 21-August 06 Member No.: 1063 |
I assume you've found the model hanging in the Smithsonian to be lacking somehow? Doug yes and even photographs of the real thing arent clear enough to explain it. The pin puller latch locks only show up in photos and couple illustrations but this detail is avoided. The cabling that connects them either runs along the etire boom along the outside or actually weaves into holes leading inside the boom from the underside. Confirmation for me could only really be determined by someone who actually was their to know for sure because its not talked about in diagrams. I could guess. The cables might go in holes but I dont really want to guess since I am creating educational art and I am kind of anal. |
|
|
May 30 2013, 10:27 AM
Post
#4
|
|
Member Group: Members Posts: 247 Joined: 17-February 07 From: ESAC, cerca Madrid, Spain. Member No.: 1743 |
I used to work at Hughes Space and Communications, which built the bus. I worked on Magellan, and there were a couple guys who had also worked on PV. They are all certainly dead or retired. But one guy who worked on Magellan (and is now retired) might know someone who might now. Its a long shot, but I'll send your question to him, and see if you get lucky.
-------------------- --
cndwrld@yahoo.com |
|
|
May 31 2013, 11:52 PM
Post
#5
|
|
Member Group: Members Posts: 613 Joined: 23-February 07 From: Occasionally in Columbia, MD Member No.: 1764 |
Does anyone know currently any of the engineers or scientists who worked directly on the Pioneer Venus Orbiter? Bernie Bienstock (now at JPL, still active) worked on Pioneer Venus (at least on the probes, not sure about the orbiter) - would be worth asking him. He'll be at the International Planetary Probe Workshop in San Jose in a couple of weeks if that is relevant. |
|
|
May 31 2013, 11:54 PM
Post
#6
|
|
Member Group: Members Posts: 613 Joined: 23-February 07 From: Occasionally in Columbia, MD Member No.: 1764 |
|
|
|
Lo-Fi Version | Time is now: 22nd September 2024 - 11:55 AM |
RULES AND GUIDELINES Please read the Forum Rules and Guidelines before posting. IMAGE COPYRIGHT |
OPINIONS AND MODERATION Opinions expressed on UnmannedSpaceflight.com are those of the individual posters and do not necessarily reflect the opinions of UnmannedSpaceflight.com or The Planetary Society. The all-volunteer UnmannedSpaceflight.com moderation team is wholly independent of The Planetary Society. The Planetary Society has no influence over decisions made by the UnmannedSpaceflight.com moderators. |
SUPPORT THE FORUM Unmannedspaceflight.com is funded by the Planetary Society. Please consider supporting our work and many other projects by donating to the Society or becoming a member. |