IPB

Welcome Guest ( Log In | Register )

2 Pages V   1 2 >  
Reply to this topicStart new topic
Ideas for a solar panel cleaner
hendric
post May 22 2008, 05:55 PM
Post #1


Director of Galilean Photography
***

Group: Members
Posts: 896
Joined: 15-July 04
From: Austin, TX
Member No.: 93



Just had an idea for a solar panel cleaner. Place a small, black tank on top of the deck. At the bottom of the tank is a one-way valve pointing into the tank. At the side of the tank is a pressure-relief valve tied to the dust removal tubes.

  1. Starting at daybreak, the tank starts filled with cold, dense atmo.
  2. As the tank warms, the pressure builds within the tank.
  3. Once the pressure reaches the cut-off of the pressure relief valve, the valve triggers and opens full-bore until the pressure difference reaches zero, and it then closes.
  4. Pressurized air comes out of the tank and blows off dust from dust-sensitive devices, camera, solar panels, view ports, etc.
  5. At night fall, the tank cools, lowering the pressure within the tank until it is below the outside pressure.
  6. The one way valve opens, refilling the tank with colder, denser air.
Because the tank isn't required to hold high pressures, it can be very light. There is about 100 degree C difference between day/night, meaning during the day the tank should reach about 50% higher pressure than night time. The pressure difference can be increased by adding a heating element.

This removes the need for storing a gas for the cleaning, as well as any need for a pump.

Ready...Set...Rip 'er apart!


--------------------
Space Enthusiast Richard Hendricks
--
"The engineers, as usual, made a tremendous fuss. Again as usual, they did the job in half the time they had dismissed as being absolutely impossible." --Rescue Party, Arthur C Clarke
Mother Nature is the final inspector of all quality.
Go to the top of the page
 
+Quote Post
ElkGroveDan
post May 22 2008, 06:01 PM
Post #2


Senior Member
****

Group: Admin
Posts: 4763
Joined: 15-March 05
From: Glendale, AZ
Member No.: 197



Creative and simple. However, my gut feeling is that the pressure differentials would not be significant so the velocity of the venting gas will be low and the duration brief. That "air" is not very dense and it requires a whole lot of energy under those circumstances to get the dust particle to move and to break whatever electrostatic bonds might be holding the dust particles in place.


--------------------
If Occam had heard my theory, things would be very different now.
Go to the top of the page
 
+Quote Post
tasp
post May 22 2008, 06:22 PM
Post #3


Member
***

Group: Members
Posts: 903
Joined: 30-January 05
Member No.: 162



Martian air is very dusty and will be passing through valve in both directions. I suspect dust will ruin the valve or it's sealing ability very quickly.

As for lack of 'pop' with the system, use a micro air pump cogged to the anemometer to pump air into the tank all day when ever wind blows. Dust problem will remain with the valving and now it is more complicated and heavier, but it will clean the panels.





Suddenly I understand mission creep.




Go to the top of the page
 
+Quote Post
jasedm
post May 23 2008, 09:54 AM
Post #4


Member
***

Group: Members
Posts: 655
Joined: 22-January 06
Member No.: 655



I understand that the dust buid-up on the arrays has been gradual, with 'cleaning events' every so often improving the situation for a time. How about a plastic 'sticker' over the panels similar to the protective plastic you get over the screen of a new mobile or camera? This could be left in place until the mission is 'power-critical' and then peeled back from the arrays (taking the dust with it) by a mechanism similar to that which opens the arrays initially.
I imagine the plastic cover would be quite inexpensive, the peeling mechanism less so.
Go to the top of the page
 
+Quote Post
MahFL
post May 23 2008, 12:56 PM
Post #5


Forum Contributor
****

Group: Members
Posts: 1372
Joined: 8-February 04
From: North East Florida, USA.
Member No.: 11



QUOTE (jasedm @ May 23 2008, 10:54 AM) *
I imagine the plastic cover would be quite inexpensive, the peeling mechanism less so.


Everything that flies in space is very expensive ! All the design, testing etc makes it so.
Go to the top of the page
 
+Quote Post
centsworth_II
post May 23 2008, 03:40 PM
Post #6


Senior Member
****

Group: Members
Posts: 2173
Joined: 28-December 04
From: Florida, USA
Member No.: 132



That would have to be some REALLY HIGH TECH plastic to withstand years of temperature swings and solar radiation.
And remain non-brittle and clear!
Go to the top of the page
 
+Quote Post
MahFL
post May 23 2008, 05:04 PM
Post #7


Forum Contributor
****

Group: Members
Posts: 1372
Joined: 8-February 04
From: North East Florida, USA.
Member No.: 11



And bloody expensive !
Go to the top of the page
 
+Quote Post
Alex Chapman
post May 23 2008, 07:51 PM
Post #8


Junior Member
**

Group: Members
Posts: 33
Joined: 5-October 06
Member No.: 1223



The real answer is just to make the solar panels large enough so that they produce enough power throughout the mission even with dust accumulation. For long duration missions go nuke and have it powered by an RTG, they really are the way to go.

Those are the engineering choices Nasa have made and personally I think they are the best.

Next to having an astronaut with a soft bristle brush brush that is.
Go to the top of the page
 
+Quote Post
Tom Tamlyn
post May 24 2008, 01:03 AM
Post #9


Member
***

Group: Members
Posts: 443
Joined: 1-July 05
From: New York City
Member No.: 424



I think "Roving Mars" mentions a similar plastic wrap roller idea. I think that JPL's eventual thinking was along the lines of Alex Chapman's comment; just making the solar panels bigger gives the biggest glow for the buck.

TTT
Go to the top of the page
 
+Quote Post
simonbp
post May 27 2008, 02:54 AM
Post #10


Junior Member
**

Group: Members
Posts: 21
Joined: 29-November 06
From: SESE/ASU
Member No.: 1437



The real problem with Mars (and Moon) dust is that it is so very electrically charged. If you walked over to one of the rovers, and tried to brush the dust off, it would probably stick to your spacesuit glove. For example, look how dirty the Apollo astronauts got (e.g. Cernan below); all that dust was electrostatic cling. So, a simple solution would be to run a ground strip from the structure of the panels to the ground (which they may already do, I don't know). A more proactive solution would be to put a negative charge on the panels (or on a transparent, conductive coating on top). This, though, would probably strain both the power and fiscal budgets...

Simon wink.gif
Attached thumbnail(s)
Attached Image
 
Go to the top of the page
 
+Quote Post
SpaceListener
post May 27 2008, 03:15 AM
Post #11


Member
***

Group: Members
Posts: 279
Joined: 19-August 07
Member No.: 3299



The Earth polar zone is very windy. I don't know if it applies the same to Mars' polar? Any way, Phoenix is programmed to have a short live and will be closed by the end of spring which is the session of low Tau factor (Atmosphere not so dusty as the ones in the summer times).

Any techniques to keep the solar panels clean s only worth when it will be living all round year as does the MER-x robots.

Hence its design is according to the Phoenix mission objectives of 3 months (by the end of August). Well, let us see if anything goes so well and its mission might be extended.
Go to the top of the page
 
+Quote Post
nprev
post May 27 2008, 03:27 AM
Post #12


Merciless Robot
****

Group: Admin
Posts: 8783
Joined: 8-December 05
From: Los Angeles
Member No.: 602



QUOTE (Alex Chapman @ May 23 2008, 12:51 PM) *
For long duration missions go nuke and have it powered by an RTG, they really are the way to go.


Gotta agree completely, here, Phoenix's solar arrays are sufficient for its mission, which has an environmentally constrained duration. Solar panels require maintenance in Martian conditions that's probably beyond the scope of automation for very long-term missions; might be also true for lunar conditions, but of course there's no wind transport of dust there so the effect should be smaller.


--------------------
A few will take this knowledge and use this power of a dream realized as a force for change, an impetus for further discovery to make less ancient dreams real.
Go to the top of the page
 
+Quote Post
Reed
post May 29 2008, 03:42 AM
Post #13


Junior Member
**

Group: Members
Posts: 87
Joined: 17-May 08
Member No.: 4114



QUOTE (Alex Chapman @ May 23 2008, 11:51 AM) *
The real answer is just to make the solar panels large enough so that they produce enough power throughout the mission even with dust accumulation. For long duration missions go nuke and have it powered by an RTG, they really are the way to go.

RTGs are unfortunately expensive, and fuel is getting scarce. The US has stopped production of Pu-238, and AFAIK the Russians are shutting theirs down as well. From what I understand, we have enough available for the currently planned missions but little beyond that.

Thinking about panel cleaning, it seems to me you don't need to run it very frequently. From the MER experience, averaging once every 3 months would probably be plenty. If you only need a few tens of cycles total, simple filters may be sufficient to make Hendrics suggestion workable from a dust POV. You'd need to be able to isolate it (lock the valves closed and cover the filters), but that should fairly straightforward. OTOH, at that level of use an expendable source might be competitive. If you use something that is liquid or solid at modest pressures, you can get a large volume without wasting too much mass on pressure vessels. CO2 seems like the obvious choice, although you may have to expend some effort keeping it in the desired state.

Larger panels are clearly the simpler (= lower technical risk) way, but being able to clean off after a major dust storm has a certain attraction.
Go to the top of the page
 
+Quote Post
Steve G
post May 29 2008, 03:57 AM
Post #14


Member
***

Group: Members
Posts: 289
Joined: 29-December 05
From: Ottawa, ON
Member No.: 624



The simplist and most weight efficient would be to have "windshield wipers". You may want to have them charged to repell dust magnetically (or attract them and then switch polarity to dump them over the side) They could be rotated after the swipe with a brush to give them a nice polish after.
Go to the top of the page
 
+Quote Post
djellison
post May 29 2008, 07:16 AM
Post #15


Founder
****

Group: Chairman
Posts: 14431
Joined: 8-February 04
Member No.: 1



QUOTE (Steve G @ May 29 2008, 04:57 AM) *
The simplist and most weight efficient would be to have "windshield wipers".


Wipers to cover all of the arrays on a vehicle would be complex, large and heavy. You want a non-moving, low mass, low volume solution. I reported on one in development at the IAC in '06 - something along these lines..
http://ieeexplore.ieee.org/Xplore/login.js...rnumber=1391965
http://ieeexplore.ieee.org/Xplore/login.js...6141.pdf?temp=x
http://www.patentstorm.us/patents/6911593/description.html
http://ieeexplore.ieee.org/Xplore/login.js...85/01190698.pdf


Doug
Go to the top of the page
 
+Quote Post

2 Pages V   1 2 >
Reply to this topicStart new topic

 



RSS Lo-Fi Version Time is now: 28th March 2024 - 09:01 AM
RULES AND GUIDELINES
Please read the Forum Rules and Guidelines before posting.

IMAGE COPYRIGHT
Images posted on UnmannedSpaceflight.com may be copyrighted. Do not reproduce without permission. Read here for further information on space images and copyright.

OPINIONS AND MODERATION
Opinions expressed on UnmannedSpaceflight.com are those of the individual posters and do not necessarily reflect the opinions of UnmannedSpaceflight.com or The Planetary Society. The all-volunteer UnmannedSpaceflight.com moderation team is wholly independent of The Planetary Society. The Planetary Society has no influence over decisions made by the UnmannedSpaceflight.com moderators.
SUPPORT THE FORUM
Unmannedspaceflight.com is funded by the Planetary Society. Please consider supporting our work and many other projects by donating to the Society or becoming a member.